Citizen BD2-2221 s Specifications

Specifications CONTROL BOARD MODEL BD2-2220/2221 Rev. 1.00 Issued on October 10, 2006

6 2.3 Print Paper Specifications (Thermal Paper) 1) Paper width : LT222X: 58 +0,-1mm, LT232X: 80 +0,-1mm 2) Paper thickness : 60µｍ ~ 150µｍ 3) Re

7 2.4 Mechanism and Peripherals Used The following mechanism and peripheral units can be connected to this control board. 1) Thermal mechanism 58 m

8 Cautions ・Using the power supply other than specified, bad effect may occur in printing operation, etc. ・Using the current without removing peak

9 3. APPEARANCE SPECIFICATIONS Weight : Approx. 37g (Only main body) Dimensions Unit: mm

10 4. Connector Connection 4.1 Interface Connectors 4.1.1 Interface Connector Pin Assignment (CN1) Pin assignment Connector used : RS PA 53313－

11 4.1.2 USB Interface Connector Pin Assignment (CN8) * Only USB model Pin assignment * Do not use a cable of longer than 5 m. PinSignal Name

12 4.1.3 CN1 Connection Example * For each interface connection, refer to each item. Notes: 1) As resistance 330Ω is

13 4.2 Mechanism Connector (CN2) 4.2.1 Mechanism Connector Pin Assignment (CN2) Pin assignment Signal Name Input/Output Function Pin LT222X LT2

14 4.2.2 FFC-compliant Cable 4.3 Head Up, Paper-End Detecting Connector (CN3, CN7) Pin assignment Pin LT2X20 LT2X21 Sensor

15 4.4 Motor Connector (CN4) Pin assignment Pin Signal Name Input/Output Function 1 MOTOR A+ Output Motor driving signal A+ 2 MOTOR B- Output

CITIZEN is a registered trade mark of CITIZEN WATCH CO., LTD., Japan. CITIZEN es una marca registrada de CITIZEN WATCH CO., LTD., Japón. Revision R

16 4.6 Paper Near-End Sensor Connector (CN6) * Option 4.6.1 Paper Near-End Sensor Connector Pin Assignment (CN6) Pin assignment Pin Signal Name In

17 5. OPERATION PANEL 5.1 Output LED 1) PE LED ON : Paper-End detection OFF : Paper Present detection 2) ERROR LED ON : Head Up (LT2220/2320 is

18 (2) Head Up error (LT2220/2320 is used and MSW3-8 OFF is set.) Explanation: ERROR LED blinks during printing and when Head Up is set (with Head

19 2) Restorable error (1) Head Up error (LT2220/2320 is used and MSW3-8 ON is set.) Explanation: ERROR LED blinks during printing and with Head Up

20 (3) Cutter lock error Explanation: Cutter operation is disabled. Abnormality occurred. PE LED: OFF ERROR LED: ERROR LED repeats blinking

21 (2) Low voltage error Explanation: Occurs when the Vp voltage supplied to the printer is lowered. If occurred, immediately turn the power OFF. P

22 4) Others (1) Paper near-end Explanation of status: When the diameter of the roll paper deceases to a certain degree (* differs with the status

23 (3) Head Up (when LT2220/2310 is used) Explanation: When Head Up is set, ERROR LED lights. PE LED: OFF ERROR LED: ON Restore Condition: Set

24 5.3 Feed Switch Function • When pressed once, paper feed of one line occurs based on the amount of line feed set by ESC 2 and ESC 3. However,

25 5.3.1 Self-printing 1) Function Function to enable the printer setting status to be verified by printing 2) Start of self-printing When the pow

CONTENTS 1. GENERAL OUTLINE...1 1.1 FEATURES...

26 5.3.2 Hexadecimal Dump Printing 1) Function Prints the data sent from the host in hexadecimal code and the corresponding characters. 2) Startin

27 5.3.3 Memory Switch Setting Mode 1) Settable memory switch MSW1、MSW2、MSW3 2) Starting memory switch setting mode With paper set and Head Up (or

28 6. INTERFACES 6.1 Bidirectional Parallel Interface (IEEE1284) 6.1.1 Specification 1) Compatibility Mode (Host → Printer Communication: Centron

29 6.1.2 Description of Input/Output Signals 1) Input/Output Signals Explanation of input/output signals [1] Input/Output Signals (Compatibility M

30 ・SELECT: Always non-active (“LOW”). ・nFAULT: Signal to set “LOW” when the printer is in the error state (negative logic). ・PE: Signal to be

31 3) Timing chart (Compatibility Mode) Data input and print timing Power supply DATA nSTROBE BUSY nACK (Note) T1，T2，T3 : 0.5 µs MIN T4

32 5) Reverse Mode (Nibble/Byte) mode allows status to be transmitted from the printer. (Using GS a, DLE EOT n, GS r, of GS I command) ・The transm

33 6.2 RS-232C Serial Interface 6.2.1 Specification 1) Synchronization: Asynchronous 2) Baud rate 2400, 4800, 9600, 19200, 38400, 57600, 115200 bp

34 ・State to become BUSY 1．Period from Reset (including reset by NV memory write command, I/F signal, and test print command) or just after printer

35 2) Buffer full state Buffer full state is when the remaining capacity of input buffer is as shown below. Table Input Buffer Full Set Value Buffe

6. INTERFACES ...28 6.1 BIDIRECTIONAL PARALLEL INTERFAC

36 6.2.3 Connection to Serial Port 1) Connection to 25-pin/9-pin serial port *The above wiring is an example of standard connection

37 7. Function Selection When using this control board, some functions can be set to default. 7.1 Jumper Turn the printer power off before changing

38 7.3 Memory Switches Memory switch is a generic name for the following: Memory switches MSW1, MSW2, and MSW3 Customize value Serial Interface Commu

39 2) Customize value Customize value can be set by the GS (E command. Function Value 1K bytes 64K bytes Specify the user NV memory capacity 128K b

40 8. PRINT CONTROL COMMANDS ○ Print Control Commands Control Command Function Mode GS P LF Printing and paper feed S・P CR Back to printing S・P

41 ○ Line Feed Span Commands Control Command Function Mode GS P ESC 2 Specifying 1/6-inch line feed rate S・P ESC 3 Setting line feed rate of mi

42 ○ Bar Code Commands Control Command Function Mode GS P GS H Selecting of printing position of HRI characters S・P GS f Selecting the

43 9. CHARACTER CODE TABLE 9.1 Code Page 9.1.1 Codepage 00H to 7FH & PC437 (USA, Europe Standard) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DL

44 9.1.2 Codepage 00H to 7FH & Katakana 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p ▁ ┴SP－タ ミ ═ ×1 XON ! 1 A Q a q ▂ ┬ º

45 9.1.3 Codepage 00H to 7FH & PC850/858 (Multilingual) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ð Ó ―1 XON ! 1 A

1 1. GENERAL OUTLINE ・This control board is used for controlling LT222X/232X through computer, etc. ・As it has a variety of functions, it can meet

46 9.1.4 Codepage 00H to 7FH & PC860 (Portuguese) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ╨ α≡1 XON ! 1 A Q a

47 9.1.5 Codepage 00H to 7FH & PC863 (Canadian-French) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É ￤ ░ └ ╨ α≡1 XON ! 1 A Q

48 9.1.6 Codepage 00H to 7FH & PC865 (Nordic) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ ╨ α≡1 XON ! 1 A Q a q ü

49 9.1.7 Codepage 00H to 7FH & PC852 (Eastern Europe) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ đ ó - 1 XON ! 1 A

50 9.1.8 Codepage 00H to 7FH & PC866 (Russian) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p ΑРа ░ └ ╨ р Ë 1 XON ! 1 A Q a q

51 9.1.9 Codepage 00H to 7FH & PC857 (Turkish) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p Ç É á ░ └ o ó ―1 XON ! 1 A Q a q

52 9.1.10 Codepage 00H to 7FH & PC864 (Arabic)

53 9.1.11 Codepage 00H to 7FH & WPC1252 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 NUL DLE 0 @ P ` p € ° À Ð à ð 1 XON ! 1 A Q a q

54 9.1.12 Codepage 00H to 7FH & Thaicode18

55 9.2 International Character Code Table Country 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E0 USA ＃ ＄ ＠ [ ╲ ] ^ ' { | } ~ 1 France ＃ ＄ à ° ç §

2 1.2 Accessories After unpacking the product, make sure the following components are present. Control board ... 1 Interface cable ... 1 (A c

3 1.4 Configuration (Block Diagram) BD2-2220/2221 BLOCK DIAGRAM CPU FLASH MEMORY 8Mbit: Fo

4 2. BASIC SPECIFICATIONS 2.1 Printing Specifications 1) Print method: Line thermal print method (Thermal printing system) 2) Dot configuration:

5 2.2 Character and Barcode Specifications 1) Character type ANK characters: 96characters Code pages: 128 characters × 12 pages International chara