Citizen CBM-272 Operations Instructions

— 1 —CBM-272

— ix —PRECAUTIONS FOR HANDLINGDo not handle the printer in the following manners, because problems may result.• Do not use any other power source besi

— 81 —This bar code, consisting of numerals only, has a variablelength of even columns. If an odd-column code istransferred, nothing will be printed.

— 82 —Example) When initially testing with the code subset B, andthen, printing the bar code, “123,” with the codesubset A• Input code : B

— 83 —GS w n[Function][Code][Range][Outline]Specifying the horizontal size (Scale factor) of bar code<1D> H <77> H <n>2 ≤ n ≤ 4Sel

— 84 —GS h n[Function][Code][Range][Outline]Specifying the height of the bar code<1D> H <68> H <n>1 ≤ n ≤ 255• Selecting bar code

— 85 —[Function][Code][Range][Outline]Selecting the printing position of HRI characters<1D> H <48> H <n>0 ≤ n ≤ 3• Selecting printin

— 86 —No Visible code[Print Results]Printed belowPrinted aboveAnd belowPrinted above

— 87 —[Function][Code][Range][Outline]Selecting the font of HRI code<1D> H <66> H <n>0 ≤ n ≤ 1• Selecting the font of HRI code in pr

— 88 —GS * n1 n2 [ d ] n1 x n2 x 8[Function][Code][Range]Defining the download, bit image<1D> H <2A> H <n1> <n2> [ <d&

— 89 —GOSUB *IMGLPRINT CHR$ (&H1D) ; "/" ; CHR$ (0) ;LPRINT CHR$ (&H1D) ; "/" ; CHR$ (1) ;LPRINT CHR$ (&H1D) ; "/

— 90 —GS / m[Function][Code][Range][Outline]Printing the download, bit image<1D> H <2F> H <m>0 ≤ m ≤ 3Prints download bit image in

— x —DAILY MAINTENANCE• At the time of maintenance, be sure to turn off the power switch of the printerand unplug it from the socket.• Use a dry soft

— 91 —GS :[Function][Code][Outline]Starting/Ending macro definition<1D> H <3A> HSpecifying starting / ending macro definition.Means termi

— 92 —GS ^ n1 n2 n3[Function][Code][Range]Executing the macro<1D> H <5E> H <n1> <n2> <n3>0 ≤ n1 ≤ 2550 ≤ n2 ≤ 2550 ≤

— 93 —DC2 A n[Function][Code][Range][Outline]Selecting a printing speed<12>H<41>H<n>0 ≤ n ≤ 1This command specifies a printing com

— 94 —DC3 n[Function][Code][Range][Outline]Switching the Red/Black printing<13>H<n>0 ≤ n ≤ 255This command selects/deselects black/red pr

— 95 —11. CHARACTER CODES TABLE11.1 International

— 96 —11.2 Code Page Katakana (Japanese)

— 97 —11.3 International Character Codes Table

— 98 —APPENDIX 1. BLOCK DIAGRAM*1 Serial Interface --- RS-232C compliantParallel Interface --- Centronics compliantROMOperationPanelPaper Near EndDC 7

— 99 —APPENDIX 2. OUTLINE DRAWING106 183126

— 100 —APPENDIX 3. WALL MOUNTING HOLES LAYOUT DRAWING2.5ø10ø1261WALL MOUNTING SCREWDIMENSIONS (REFERENCE)ø3.1ø5.742.3322.5117.253.5R3.75R5.75R3.755.75

— xi —DANGER● To prevent electrolyte leakage, heat build-up, or bursting:• Do not throw battery packs into fire or expose to any heat source.• Do not

— 101 —GERMAN

— 102 —<VORSICHT>• Bitte lesen Sie diese Bedienungsanleitung vor dem Betrieb des Druckersaufmerksam durch und bewahren Sie die Anleitung anschli

— 103 —ZU BEACHTENDE SICHERHEITSMASSREGELNZur Vermeidung von Gefahren gegenüber dem Bediener und anderen Personenund Sachschäden sind die folgenden Vo

— 104 —WARNUNG●Beim Betrieb des Druckers sind die nachfolgenden Vorsichtsmaßregeln unbedingt zu beachten. EineMißachtung dieser Hinweise kann zu Schäd

— 105 —VORSICHTSMASSREGELN FÜR DIE AUFSTELLUNG•Den Drucker nicht an Plätzen abstellen oder betreiben, an denen er Feuer, Feuchtigkeit oder direkterSon

— 106 —VORSICHTSMASSREGELN FÜR DIE HANDHABUNGZur Vermeidung von Problemen sind bei der Handhabung des Druckers diefolgenden Vorsichtsmaßregeln zu beac

— 107 —TÄGLICHE WARTUNG• Bei der Wartung immer den Netzschalter des Druckers auf Aus stellen und denStecker aus der Steckdose ziehen.• Schmutz und Sta

— 108 —GEFAHR!● Zum Schutz vor einem Austreten von Batterieflüssigkeit und Heißwerden oderPlatzen des Akkus:• Akkus nicht verbrennen oder Wärmequellen

— 109 —WARNUNGEN● Wenn am Drucker oder dem enthaltenen Akku Spuren von auslaufenderBatterieflüssigkeit, Verfärbungen, Verformungen oder ungewöhnlicher

— 110 —VORSICHT● Den Akku keinen heftigen Stößen aussetzen und nicht auf harte Flächen fallenlassen.●Den Akku keiner direkten Sonnenbestrahlung ausset

— xii —WARNINGS● If the printer or its internal battery pack shows any sign of electrolyte leakage,discoloration, deformation, or odd smell, immediate

— 111 —AKKU-LEBENSDAUER• Der Akku ist für eine Lebensdauer von über 300 Lade-/Entladezyklen über 3 bis 5Jahre (bei Raumtemperatur) bei sachgemäßer Ver

— 112 —4. BETRIEB4.1 Anschließen des NetzteilsDas Gerät ausschalten.Den Kabelstecker des Netzteils in den Betriebsstromeingang an der Rückseite desDru

— 113 —4.2 Auswechseln des Akkus4.2.1 Entnehmen des AkkusDen Netzstecker aus der Netzsteckdose ziehen.Den POWER-Schalter auf OFF stellen.Den Akkufachd

— 114 —4.2.2 Einsetzen des AkkusDen Akku mit der Etikettseite nach oben richten und die Stecker desKabelsatzes miteinander verbinden.Den Akku in das A

— 115 —4.3 Laden des AkkusDer Akku kann gepuffert und ungepuffert geladen werden. Durch gepuffertesLaden kann er während des laufenden Betriebs aufgel

— 116 —4.3.3 Akkugespeister BetriebDer Drucker wird nur dann aus dem Akku mit Strom versorgt, wenn das Netzteilnicht angeschlossen ist. Nach dem Einsc

— 117 —4.3.4 Prüfen der AkkuspannungWenn die Akkuspannung unter 5.6 V absinkt, schaltet die Spannungsprüffunktionden Drucker automatisch aus (POWER-Sc

— 118 —VORSICHT:• Wenn am Drucker oder dem enthaltenen Akku Spuren von auslaufenderBatterieflüssigkeit, Verfärbungen, Verformungen oder ungewöhnlicher

— 119 —4.4 Rückstellungen4.4.1 Rückstellungen bei laufendem DruckbetriebBei akkugespeistem Betrieb kann es vorkommen, daß während des Druckensdichter

— 120 —4.5 Stromsparmodus und automatische AbschaltungUm einen unnötigen Verbrauch von Akkusstrom zu vermeiden, schaltet sich derDrucker automatisch a

— xiii —CAUTIONS● Do not give the battery pack a severe jolt or drop it on a hard surface.●To prevent electrolyte leakage or lowered battery performan

— 121 —4.6 Anschließen des SchnittstellenkabelsDas Gerät ausschalten. (Paßseite eingeschlossen)Die Ober- und Unterseite der Kabelkontakte prüfen, und

— 122 —Sicherstellen, daß das Gerät eingeschaltet ist.Den Kopfanhebe-Hebel zu dieser Seite ziehen, um den Druckkopf anzuheben.Wenn sich weiteres Papie

— 123 —VORSICHT:• Wenn die Papierrolle schlaff ist, das Papier zurückwickeln, um den Durchhang zubeheben.• Wenn die Papierrolle geneigt ist, den Kopfa

— 124 —4.8 Entnehmen der eingesetzten PapierrolleDie Druckerabdeckung entfernen.Den Kopfanhebe-Hebel heben.Vorsichtig das Papier zur nahen Seite herau

— 125 —4.9 Beseitigen von PapierstauDas Gerät ausschalten.Die Druckerabdeckung entfernen.Die Papierrolle in der Nähe des Papiereinzugschachts abschnei

— 126 —VORSICHT:• Diese Arbeit nicht sofort nach dem Drucken ausführen, da sich der Druckkopf starkerhitzt.• Beim Abnehmen der Druckwalzeneinheit imme

— 127 —123454.12 Papiermangel-FunktionWenn das Papier fast verbraucht ist, informiert der PNE-Sensor den Hostcomputer,daß das Papier fast verbraucht i

— 128 —(2) Druckmenge nach Erkennung von PNEWenn PNE aktiviert ist, kann eine druckbare Menge nach der PNE-Erkennungeingestellt werden. PNE wird erkan

— 129 —4.13 AutoladefunktionDieser Drucker hat eine Funktion zur automatischen Papiereinstellung. Wenn derPapierendesensor, Papiermangelsensor und Kop

— 130 —StatusLadenVoll geladenDruckenLadenVoll geladenPOWER-Lampe (grün)OffOffLeuchtetLeuchtetFunktionLaden desAkkusGepuffertesLaden4.15 Bedienfeld un

— xiv —BATTERY PACK LIFE• The battery pack is designed to have life span of more than 300 recharging cyclesor 3 to 5 years (at room temperature), prov

— 131 —<Fehler-Einzelheiten>Kopfanheben ----- Tritt auf, wenn der Kopfanhebe-Hebel angehoben ist. DerDrucker kann nicht Papier zuführen oder dru

— 132 —4.16 Rot/Schwarz-Druck (Vorsichtsmaßregeln)(1) PapiersortenDas rote und schwarze Zweifarb-Thermalpapier ändert seine Farbe durchSteuerung der a

— 133 —123DS1 (für serielle Schnittstelle/parallele Schnittstelle)No.12345678FunktionPNE-WahlCR-UmschaltenDruckdichteUnterspannungssignalAutoladenDTR/

— 134 —DS2-4OFFOFFOFFOFFOFFOFFOFFOFFONONONONONONONONDS2-3OFFOFFOFFOFFONONONONOFFOFFOFFOFFONONONONDS2-2OFFOFFONONOFFOFFONONOFFOFFONONOFFOFFONONParitätK

— 135 —DS2-1OFFONOFFONKeine Daten/Bedienung10 Min.↑20 Min.30 Min.StromsparmodusUnbegrenzt10 Min.↑↑AnmerkungenAutom. Abschaltung deaktiviert10 Min. ohn

— 136 —5.3 Jumperdraht-FunktionDie Jumperdrähte sind werksseitig vor dem Versand eingestellt. Die folgende Listezeigt die grundlegende Einstellung bei

— 137 —9. WARTUNG UND DIENSTBitte wenden Sie sich an die folgenden Stellen für weitergehende Informationen.Nordamerika Andere GebieteCBM America Corpo

Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, JapanHead Office Tel: (+81-3) 5345-7540 Fax: (+81-3) 5345-754101E-

— xv —CONTENTS1. OUTLINE ... 11.1 Features ...

— xvi —4.11 Paper End Function ... 244.12 Paper Near End Function...

— xvii —10. PRINT CONTROL FUNCTIONS ... 4410.1 Command List ...

— xviii —<<<German>>>4. BETRIEB ... 1124.1 Anschließe

— i —Manufacturer’s Name : Japan CBM CorporationManufacturer’s Address : CBM Bldg., 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, JapanDeclare the Prod

— 1 —1. OUTLINEThis compact battery-powered line thermal printer is designed for use with dataterminals and instrumentation equipment. Its abundant b

— 2 —1.2 UnpackingWhen unpacking the package, confirm that the following parts are provided:• Printer body (including battery pack) 1 unit• Sample pap

— 3 —2. BASIC SPECIFICATIONS2.1 Model ClassificationsThe models are classified by the following designation method:CBM-272 - R F 120*Special Swit

— 4 —2.2 Basic SpecificationsPrinting systemPrinting widthDot densityPaper feed pitchPrinting speedPrinting columns andcharacter sizeLine intervalCha

— 5 —AC adapterTypeAC cordSupply voltagePower consumptionWeightOuter dimensionsOperating temperature andhumidityStorage temperature andhumidityReliabi

— 6 —2.3 Paper Specifications2.3.1 Recommended Paper• Type : Thermal paper• Paper width : 58 + 0/– 1 mm• Paper thickness : 60~75µm• Roll diameter : ø

— 7 —2.3.2 Printing PositionThermal paper2.3.3 Printing Head and Paper Cutter LayoutPaper Width: 58 mmPrinting Area: 48 mmAbout 4 mm About 6 mmPaper C

— 8 —3. OUTER APPEARANCE AND COMPONENT PARTSUpper Cover(2) POWER Lamp(3) ERROR Lamp(4) PAPER lamp(5) FEED Switch(14) Printer CoverBottom Cover(1) POWE

— 9 —(1) POWER switchTurns on/off the power for the printer body.(2) POWER lamp (Green/Red)Comes on in green when the POWER switch is set to ON.This l

— 10 —4. OPERATION4.1 Connecting AC AdapterTurn off the power.Connect the cable connector of the AC adapter to the power connector located onthe back

— ii —IMPORTANT SAFETY INSTRUCTIONS• Read all of these instructions and save them for future reference.• Follow all warnings and instructions marked o

— 11 —4.2 Replacing the Battery Pack4.2.1 Removing the Battery PackUnplug the AC cord from the wall outlet.Set POWER switch to OFF.Remove the battery

— 12 —4.2.2 Installing the Battery PackWith the labeled side of battery pack facing up, connect the batteryconnecter.Insert the battery pack into the

— 13 —4.3 Charging the Battery PackThe battery pack can be charged in either non-floating or floating modes. Infloating mode, the battery pack can be

— 14 —4.3.3 Battery-Powered OperationThe printer is powered only from the battery pack if the AC adapter is leftdisconnected. The printer is ready to

— 15 —4.3.4 Battery Voltage CheckIf the battery voltage drops below 5.6 V, the voltage check feature automaticallyshuts off the printer (POWER switch

— 16 —CAUTION:• If a charging cycle does not complete within the specified time, stop charging at thatpoint. This will help prevent electrolyte leakag

— 17 —4.4 Reset4.4.1 Reset during a Printing TaskThe printer, when operating on battery power, may reset (POWER lamp goes off)while it is printing den

— 18 —4.5 Power Save and Auto Power OffTo save unnecessary battery consumption, the printer automatically enters thepower save mode if it receives no

— 19 —4.6 Connecting Interface CableTurn off the power. (Mating side included)Check the top and bottom of cable terminals, and connect to the interfa

— 20 —Make sure that the power is turned on.Pull the head-up lever to this side to raise up the printing head.If there is still some paper remaining a

— iii —WICHTIGE SICHERHEITSANWEISUNGEN• Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf.• Befolgen Sie alle auf dem

— 21 —CAUTION:• If the paper roll is still slack, rewind the paper to remove the slack.• If the paper roll is tilted, raise the head-up lever to corre

— 22 —4.8 How to Remove Remaining Paper RollRemove the printer cover.Raise the head-up lever.Gently pull out the paper to the near side. If the paper

— 23 —4.9 Eliminating the Paper JamTurn off the power.Detach the printer cover.Cut the paper roll near the paper insertion slot.Raise the head-up leve

— 24 —CAUTION:• Do not carry out this work just after printing because the printing head is very hot.• Be sure to turn off the power when detaching th

— 25 —123454.12 Paper Near End FunctionIf the paper is running out, the PNE sensor informs the host computer that thepaper is running out, by means of

— 26 —(2) Print amount after detecting PNEWhen PNE is enabled, a printable amount after PNE detection can be adjusted.PNE is detected when the remaini

— 27 —4.13 Auto-Loading FunctionThis printer has a function to automatically set the paper. If the paper end sensor,near paper end sensor, and head-u

— 28 —StatusChargingFully chargedPrintingChargingFully chargedPOWERLamp(Green)OffOffLightingLightingItemChargingbattery packFloatingcharging4.15 Opera

— 29 —<Error Details>Head-up ----- Occurs when the head-up lever is raised. The printer cannotfeed the paper or print. The parallel interface

— 30 —4.16 Red/Black Print (Precautions for Use)(1) Types of paperThe red and black two-color thermal paper changes its colors by controllingthe energ

— iv —IMPORTANT: This equipment generates, uses, and can radiate radio frequencyenergy and if not installed and used in accordance with the instructio

— 31 —123DS1 ( For Serial Interface/Parallel Interface)No.12345678FunctionPNE selectionCR switchingPrint densityLow Voltage signalAuto-loadingDTR/DSR,

— 32 —DS2-4OFFOFFOFFOFFOFFOFFOFFOFFONONONONONONONONDS2-3OFFOFFOFFOFFONONONONOFFOFFOFFOFFONONONONDS2-2OFFOFFONONOFFOFFONONOFFOFFONONOFFOFFONONParityNon

— 33 —DS2-1OFFONOFFONNo data, No operation10 min.↑20 min.30 min.Power SaveNo time limit10 min.↑↑RemarksAuto Power Off is inactiveNo data, no operation

— 34 —5.3 Jumper Wire FunctionThe jumper wires have been set at shipment. The following lists the basic settingsat shipment. Check the settings by p

— 35 —6. PARALLEL INTERFACE6.1 Specifications• Data input system : 8-bit parallel (DATA1 to DATA8)• Control signals : ACK, BUSY, STROBE, FAULT, SELECT

— 36 —6.3 Input and Output Signals6.3.1 Input and Output Signals(1) Input signals to the printer• DATA : 8-bit parallel signal (Positive logic)• STROB

— 37 —[Printer Side] [Host Side]6.3.3 Timing ChartData Input and Print Timings6.3.4 Data Receiving ControlThe data can be received from the host when

— 38 —7. SERIAL INTERFACE7.1 Specifications(1) Synchronous system : Asynchronous(2) Baud rate : 1,200, 2,400, 4,800, 9,600, 19,200 bps (Selected by th

— 39 —[Note] 1. The RS-232C signals are based on the EIA RS-232C.2. The received data should be always maintained in the Mark status whenno data is be

— 40 —7.3.2 Data Configuration(1) Start bitThe system reads the status again after a lapse of 1/2 bit from a fall edge fromthe mark to space, and if i

— v —<CAUTIONS>• Prior to using the printer, be sure to read this User's Manual thoroughly. Pleasekeep it handy for reference whenever it

— 41 — 7.3.4 Data Receiving ControlIf DTR/DSR control has been selected, the data from the host side will be receivedwhen the BUSY signal is at “Low,”

— 42 —8. POWER CONNECTORThis connector is to supply the power from the special AC adapter(27AD).Connector SchematicNo.12Function7.2VGNDJack used : HEC

— 43 —9. MAINTENANCE AND SERVICEFor the information on maintenance and service, please contact our dealer or atthe following address.North America Oth

— 44 —10. PRINT CONTROL FUNCTIONS10.1 Command List12345678910111213141516171819202122232425262728293031CommandHTLFCRESC SPESC !ESC %ESC &ESC

— 45 —3233343536373839404142CommandGS kGS wGS hGS HGS fGS *GS /GS :GS ^DC2 ADC3Code1DH 6BH n [‘d’] k00H1DH 77H n1DH 68H n1DH 48H n1DH 66H n1

— 46 —10.2 Command Details10.2.1 Descriptions of Each ItemXXXXX[Function][Code]Command FunctionA sequence of code constituting a command is represente

— 47 —10.2.2 Command DetailsHT[Function][Code][Outline]Horizontal tab<09> HShifts the printing position to the next horizontal tabposition.• Ign

— 48 —LF[Function][Code][Outline]Printing and Paper Feed<0A>HPrints data inside the input buffer and feeds lines based onthe line feed amount ha

— 49 —CR[Function][Code][Outline]Print<0D>H1) When DS1-2 is OFF:This command is ignored.2) When DS1-2 is ON:With data held inside the internal p

— 50 —ESC SP n[Function][Code][Range][Outline]Setting the right spacing of the character<1B> H <20> H <n>0 ≤ n ≤ 32The rightward s

— vi —SAFETY PRECAUTIONS — BE SURE TO OBSERVEIn order to prevent hazards to an operator or other persons and damage toproperty, be sure to observe the

— 51 —ESC ! n[Function][Code][Range][Outline]Collective specifying the printing mode<1B> H <21> H <n>0 ≤ n ≤ 255Printing mode is a

— 52 —Font AFont BFont A + EmphasisFont B + Emphasis + Quadruple + UnderlineFont A + UnderlineFont A + Double WidthFont A + Double Height∨∨ ∨∨∨∨∨[Prin

— 53 —ESC % n[Function][Code][Range][Outline]Specifying/Canceling download character set<1B> H <25> H <n>0 ≤ n ≤ 255Specifying/can

— 54 —ESC & s n m [a Page s x a] m–n+1[Function][Code]Defining the download characters<1B> H <26> H <s> <n> <m>

— 55 —[Sample Program][Print Results]See Sample Program and Print Results for ESC %.[Example]Create each data bit by setting “1” for a printed dot and

— 56 —ESC * m n1 n2 [ d ] k[Function][Code][Range]Specifying the bit image mode<1B> H <2A> H <m> <n1> <n2> [<d>

— 57 —[Example][Sample Program]LPRINT CHR$ (&H1B) ; "*" ;LPRINT CHR$ (0) ; CHR$ (20); CHR$ (0) ;GOSUB *IMG1LPRINT CHR$ (&HA) ;LPRINT

— 58 —[Function][Code][Range][Outline]Specifying/Canceling underline<1B> H <2D> H <n>0 ≤ n ≤ 2Specifying/canceling an underline.• Ty

— 59 —ESC 2[Function][Code][Outline][See Also][Sample Program]Specifying 1/6-inch line feed rate<1B> H <32> HThe line feed rate per line

— 60 —ESC 3 n[Function][Code][Range][Outline]Setting line feed rate of minimum pitch<1B> H <33> H <n>0 ≤ n ≤ 255The line feed rate

— vii —WARNING● Never handle the printer in the following manners, as it may break, become outof order, or overheat causing smoke and resulting in fir

— 61 —ESC = n[Function][Code][Range][Outline]Data input control<1B> H <3D> H <n>0 ≤ n ≤ 255Selecting equipment in which data input

— 62 —ESC @[Function][Code][Outline]Initializing the printer<1B> H <40> HClears data stored in the print buffer and brings varioussetting

— 63 —ESC D [ n ] k NUL[Function][Code][Range]Setting horizontal tab position<1B> H <44> H [<n>] k <00> H1 ≤ n ≤ 2550 ≤ k

— 64 —ESC E n[Function][Code][Range][Outline]Specifying/Canceling highlighting<1B> H <45> H <n>0 ≤ n ≤ 255Specifying/canceling the

— 65 —ESC G n[Function][Code][Range][Outline]Specifying/Canceling double printing<1B> H <47> H <n>0 ≤ n ≤ 255Specifying/canceling

— 66 —ESC J n[Function][Code][Range][Outline]Printing and Feeding paper n/203 inch<1B> H <4A> H <n>0 ≤ n ≤ 255Prints data inside t

— 67 —ESC R n[Function][Code][Range][Outline]Selecting the international character set<1B> H <52> H <n>0 ≤ n ≤ 10Depending on the

— 68 —[Function][Code][Range][Outline]Specifying/Canceling 90°-right- turned characters<1B> H <56> H <n>0 ≤ n ≤ 1Specifying/cancelin

— 69 —ESC a n[Function][Code][Range][Outline]Aligning the characters<1B> H <61> H <n>0 ≤ n ≤ 2All the printed data within one line

— 70 —ESC c 3 n (Parallel Interface Only)[Function] Selecting the paper near end sensor valid for a paper endsignal output<1B>H<63&g

— viii —PRECAUTIONS FOR INSTALLATION• Do not use or store the printer in a place exposed to fire, moisture, or directsunshine, or in a place near a he

— 71 —ESC c 5 n[Function][Code][Range][Outline]Enabling/Disabling the panel switches<1B> H <63> H <35> H <n>0 ≤ n ≤ 255Sele

— 72 —ESC d n[Function][Code][Range][Outline]Printing and feeding the paper by n lines<1B> H <64> H <n>0 ≤ n ≤ 255Prints data insi

— 73 —ESC n n[Function][Code][Range][Outline]Setting a remaining amount of printout<1B>H<6E>H<n>0 ≤ n ≤ 255 (“n” in the 2nd byte d

— 74 —ESC t n[Function][Code][Range][Outline]Selecting the character code table<1B> H <74> H <n>0 ≤ n ≤ 1Selecting Page n on the c

— 75 —ESC v (Serial Interface Only)[Function][Code][Outline]Transmitting the printer status<1B> H <76> H• Current printer status is trans

— 76 —ESC { n[Function][Code][Range][Outline]Specifying/Canceling Inverted Characters<1B> H <7B> H <n>0 ≤ n ≤ 255Specifying/Cancel

— 77 —ESC $ n1 n2[Function][Code][Range]Specifying the absolute positions<1B> H <24> H < n1> <n2>0 ≤ n1 ≤ 2550 ≤ n2 ≤ 1The

— 78 —ESC \ n1 n2[Function][Code][Range]Specifying the relative positions<1B> H <5C> H <n1> <n2>0 ≤ n1 ≤ 2550 ≤ n2 ≤ 255Th

— 79 —GS k n [ d ] k NUL[Function][Code]Printing the bar code<1D> H <6B> H <n> [ <d> ] k <00> H*<d> = charact

— 80 —[Print Results][Description of BarCodes]UPC-A<For print examples, see Page 82.>When the data “123” is printed with the code 39This bar c