LINE THERMAL PRINTERMODELiDP3210
iDP3210 User’s ManualCITIZENThis Caution label is attached in the following position.Make sure to use this equipment properly reading the cautions for
iDP3210 User’s ManualCITIZENORDINALY MAINTENANCE• Make sure to maintain the equipment after switching OFF the power.• When cleaning the platen of pr
iDP3210 User’s ManualCITIZENCONTENTS1. OUTLINE...
iDP3210 User’s ManualCITIZEN6.1.4 Electrical Characteristics...
iDP3210 User’s Manual1CITIZEN1. OUTLINEThis printer, a small-sized line thermal printer, has been developed to be applicable to various datacommunicat
iDP3210 User’s Manual2CITIZEN(2) When using the printer, remove the protective paper of the thermal head in the following procedures:1) Open the print
iDP3210 User’s Manual3CITIZEN2. BASIC SPECIFICATIONS2.1 Model ClassificationiDP3210 -R F 120 AC Adapter 120 : for AC 120V
iDP3210 User’s Manual4CITIZEN2.2 Basic SpecificationsItem DescriptionPrinting system Line thermal dot printing systemPrint width 73.92 mm/448 dotsDot
iDP3210 User’s Manual5CITIZEN2.3 Printing Paper Specifications2.3.1 Recommended PaperType : Thermal paperPaper width : 80+0mmPaper thickness : 65 ± 5
iDP3210 User’s Manual6CITIZEN2.3.2 Printing position2.3.3 Head and Cutter Layout
iDP3210 User’s Manual CITIZEN Declaration of Conformity Manufacturer’s Name : : Japan CBM Corporation Manufacturer’s Address : CBM Bldg.,5-6
iDP3210 User’s Manual7CITIZEN3. OUTER APPEARANCE AND COMPONENTS
iDP3210 User’s Manual8CITIZEN4. OPERATION4.1 Connecting AC Adapter(1) Turn off the power switch.(2) Holding the AC Adapter cable connector with its ar
iDP3210 User’s Manual9CITIZEN4.2 Connecting Interface Cable(1) Turn OFF the power switch. (Both for the printer and the host side.)(2) Confirming the
iDP3210 User’s Manual10CITIZEN4.3 Connecting Drawer Kickout Connector(1) Turn OFF the power switch.(2) Confirming the up and down side of the drawer k
iDP3210 User’s Manual11CITIZEN4.4 Setting the Roll PaperCAUTION Do not use the roll paper other than the specified in this manual.In case of using the
iDP3210 User’s Manual12CITIZENCAUTION In case the slack of paper remains, adjust the position of roll paper pulling paper guide tothe front side. In c
iDP3210 User’s Manual13CITIZEN4.5 How to Remove Remaining Roll Paper(1) Open the printer cover.(2) Holding the paper guide, pull it in the arrowed dir
iDP3210 User’s Manual14CITIZENCAUTION Since print head and motor are hot, do not carry out this action right after printing. In caseof moving the head
iDP3210 User’s Manual15CITIZEN4.7 Canceling Cutter Lock(1) As referring to "4.6 Removing Paper Jam", remove the roll paper remains inside th
iDP3210 User’s Manual16CITIZEN4.8 Cleaning Print Head(1) As referring to "4.6 Removing Paper Jam”, remove the platen roller unit.(2) Using a cott
iDP3210 User’s ManualCITIZENIMPORTANT SAFETY INSTRUCTIONS• Read all of these instructions and save them for future reference.• Follow all warnings a
iDP3210 User’s Manual17CITIZEN4.9 Operation Panel and Display of Error(1) POWER LAMP (Green)With power switch is turned ON, this lamp lights up. Furth
iDP3210 User’s Manual18CITIZENPrint Head overheat : To protect print head from excessive heat, in case the temperature of print head goeshigh(approx.
iDP3210 User’s Manual19CITIZEN5. Dip Switch Setting5.1 Location of Dip Switch(1) Turn OFF the power switch.(2) Remove the rear cover.(Remove it by tak
iDP3210 User’s Manual20CITIZEN5.2 Dip Switch SettingDS1 Function ON OFF Factory SettingDS1-1 Paper cutter Enabled Disabled ONDS1-2 Cover open Disabled
iDP3210 User’s Manual21CITIZEN6. INTERFACE (Connecting with Peripheral Equipment)6.1 Parallel Interface6.1.1 SpecificationsData input method : 8 bit p
iDP3210 User’s Manual22CITIZEN6.1.3 I/O SIGNALS(1) Input Signals to the Printer• DATA : 8-bit parallel signal (positive logic)• STB : Strobe signal to
iDP3210 User’s Manual23CITIZEN6.1.4 Electrical Characteristics(1) Input Signal LevelAll the input signals are at C-MOS level."HIGH" level :
iDP3210 User’s Manual24CITIZEN6.1.5 TIMING CHART(1) Data Input and Printing TimingT1, T2, T3 : 0.5 sMINT4 : 270 ns MAXT5 : 2.3 sTYPT6 : 500 ms MIN (On
iDP3210 User’s Manual25CITIZEN6.2SerialInterface6.2.1Specifications(1) Data transfer system : Asynchronous(2) Baud rates150, 300, 600, 1200, 2400, 480
iDP3210 User’s Manual26CITIZEN6.2.2 Connector’s Pin ConfigurationsNo. Signal Name I/O Function1FG FrameGrand7 GND Signal GND3 RD Input Receiving data2
iDP3210 User’s ManualCITIZENWICHTIGE SICHERHEITSANWEISUNGEN• Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf.• Bef
iDP3210 User’s Manual27CITIZEN6.2.3 I/O SIGNALS(1) RDSerial receiving data signal. On occurrence of framing error, overrun error, or parity error, the
iDP3210 User’s Manual28CITIZEN6.2.4 Data Configuration------- tMarkSpace(1) (2) (3)(1) Start bit(2) Data bit (+ parity bit)(3) Stop bit ( 1 or more )(
iDP3210 User’s Manual29CITIZEN6.2.5 Error DetectionParity, framing, and overrun are detected. On detection of any error, the data are stored in the bu
iDP3210 User’s Manual30CITIZEN6.2.8 ELECTRICAL CHARACTERISTICS(1) RS-232C CircuitInput (RD, DSR)[Printer Side] [Host Side]Equivalent to Max 232Output
iDP3210 User’s Manual31CITIZEN7. DRAWER KICKOUT CONNECTOR7.1 Specifications(1) Drawer-Kick Drive SignalPulses specified by ESCp are output. Also, SW(+
iDP3210 User’s Manual32CITIZEN8. POWER SUPPLY CONNECTOR SPECIFICATIONSThis is the connector for power supply from exclusive AC Adapter.Connector’s Pin
iDP3210 User’s Manual33CITIZEN9. PRINT CONTROL FUNCTION9.1 Command ListControl Code Function Page1HTHorizontal tab command342CRPrint command343LFPrint
iDP3210 User’s Manual34CITIZEN9.2 Command Details(1) Horizontal Tab Command (HT)Code : (09)hShifts the printing position to the next horizontal tab po
iDP3210 User’s Manual35CITIZEN(5) Specifying Collectively the Print Mode (ESC ! n)Code : [1Bh] + [21h] + n*{0≤ n ≤ FF} Data is described in Hex code.P
iDP3210 User’s Manual36CITIZEN(7) Defining Download Character (ESC & s n m a (D1D2 ~ Dn)Code : [1B]h + [26]h + s +n +m +a +Dn* {s = 02}{20 (Hex) ≤
iDP3210 User’s ManualCITIZENIMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if notinstalled and used in accordan
iDP3210 User’s Manual37CITIZEN(8) Specifying the Bit Image Mode (ESC * m n1 n2 D1 ~ Dn)Code:[1B]h+[2A]h+m+n1+n2+Dn* {m= bit imagemode (See the table b
iDP3210 User’s Manual38CITIZEN(9) Specifying/ Canceling Underline (ESC - n)Code: [1B]h + [2D]h + n*{0≤ n ≤ 02} Data is described in Hex code.Specifyin
iDP3210 User’s Manual39CITIZEN(13) Setting Horizontal Tab Position (ESC D n NUL)Code : [1B]h + [44]h + n [00]h*{0≤ n ≤ FF} Dta is described in Hex cod
iDP3210 User’s Manual40CITIZEN(15) Specifying/canceling Double Printing (ESC G n)Code : [1B]h + [47]h + n*{0≤ n ≤ FF} Data is described in Hex code.Sp
iDP3210 User’s Manual41CITIZEN(17) Selecting International Characters (ESC R n)Code : [1B]h + [52]h + n*{0≤ n ≤ 0A) Data is described in Hex code.Sele
iDP3210 User’s Manual42CITIZEN(19) Setting of paper end detector available for print stopCode : [1B]h + [63]h + [34]h + n*{0≤ n ≤ FF} Data is describe
iDP3210 User’s Manual43CITIZEN(22) Generating specified Pulse (ESC p m n1 n2)Code : [1B]h + [70]h + m + n + n2* {m = connector pin No. (See table belo
iDP3210 User’s Manual44CITIZEN(24) Transmitting the printer status (ESC v)Code : [1B]h + [76]hCurrent printer status is transmitted.•Status sent out c
iDP3210 User’s Manual45CITIZEN(25) Transmitting the status of Peripheral Equipment (ESC u n)Code : [1B]h + [75]h + n*{n=0}Current status of connector
iDP3210 User’s Manual46CITIZEN(26) specifying/Canceling Inverted CharactersCode : [1B]h + [7B]h + n*{0≤ n ≤ FF} Data is described in Hex code.Specifyi
iDP3210 User’s ManualCITIZEN<CAUTIONS>1. Before using the equipment, be sure to read this User's Manual thoroughly. Please keep this with c
iDP3210 User’s Manual47CITIZENn (Hex) Type0Canceling90°-right- turned Characters1Specifying90°-right- turned Characters• The initial value of n is &qu
iDP3210 User’s Manual48CITIZEN(30) Bar Code Printing (GS k n Dn NUL)Code : [1D]h + [6B]h + n + Dn + [00]h*{0≤ n ≤ 7} Data are described in Hex code.Sp
iDP3210 User’s Manual49CITIZEN(32) Selecting Bar Code Height (GS h n)Code : [1d]H + [68]H + N*{1≤ n ≤ FF} Data is described in Hex code.Selecting bar
iDP3210 User’s Manual50CITIZEN(34) Defining Download Bit Image (GS * n1 n2 Dn)Code : [1D]h + [2A]h + n1 + n2 Dn*{1≤ n1 ≤ FF}{1 ≤ n2 ≤ 48}{n1 × n2 ≤ 13
iDP3210 User’s Manual51CITIZEN(35) Printing Download Bit Image (GS / m)Code : [1D]h + [2F]h + m*{0≤ m ≤ 3} Data is described in Hex code.Prints downlo
iDP3210 User’s Manual52CITIZEN(37) Macro Execution (GS^ n1 n2 n3)Code : [1D]h + [5E]h + n1 + n2 + n3*{0≤ n1 ≤FF}{0 ≤ n2 ≤ FF}{0 ≤ 3 ≤ 1} Data is descr
iDP3210 User’s Manual53CITIZEN(38) Data Input Control (ESC = n)Code : [1B]h + [3D]h + n*{0≤ n ≤ FF} Data is described in Hex code.Selecting equipment
iDP3210 User’s Manual54CITIZEN(39) Aligning the characters (ESC a n)Code : [1b]h + [61]h + n*{0≤ n ≤ 2} Data is described in Hex code.All the printed
iDP3210 User’s Manual55CITIZEN10. CHARACTER CODETABLE10.1 International (IBM Character #2)
iDP3210 User’s Manual56CITIZEN10.2 International Character Code Table
iDP3210 User’s ManualCITIZENWARNING• Do not subject this equipment to excessive force or shocks such as by treading on it, dropping it orhitting it.•
iDP3210 User’s Manual57CITIZENAppendix 1 Outline Drawing1.1 Outler Drawing of Printer (Model : iDP3210)
iDP3210 User’s Manual58CITIZEN1.2 Outer Drawing of AC Adapter (Model : 30AD)
iDP3210 User’s Manual59CITIZENAppendix 2 Block Diagram
Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, JapanHead Office Tel: (+81-3) 5345-7540 Fax: (+81-3) 5345-754115E-
iDP3210 User’s ManualCITIZENPRECAUTIONS FOR INSTALLATION• Do not install or store this printer near fire, water, a heater, in the direct sunshine in
iDP3210 User’s ManualCITIZENCAUTION FOR HANDLINGDo not carry out the following operation, since they may be cause of breakage.• Do not carry out blan
Comments to this Manuals