LINE THERMAL PRINTERMODEL CT-S280User’s Manual
— 6 —Caution label is attached on the position shown in the following figure. Carefullyread the precautions in handling before using the printer.THIS
— 7 —Observe the following precautions for daily maintenance.● When cleaning the printer, always turn it off and unplug it from thesupply outlet.● Use
— 8 —THE TABLE OF CONTENTS1. GENERAL OUTLINE ...91.1 Features ...
— 9 —1. GENERAL OUTLINEThe CT-S280 is a thermal line printer designed for use with a broad array ofterminal equipment including, data, POS, and kitch
— 10 —CT-S 280 RS U - WHCase colorWH: Cool whiteBK: BlackDestination (Letters + Power cord)J: JapanE: EuropeU: USA1.3 Model ClassificationThe prin
— 11 —Item SpecificationsModel CT-S280RSU CT-S280RSE CT-S280RSJCT-S280PAU CT-S280PAE CT-S280PAJCT-S280UBU CT-S280UBE CT-S280UBJPrint method Line therm
— 12 —2. EXPLANATION OF PRINTER PARTS2.1 Printer AppearancePaper coverPower switchCover open buttonOperation panel● Paper coverPaper is located insi
— 13 —● POWER LEDLights when the printer power is on and goes off when the printer power isoff. May blink or light in a special mode or in case of a
— 14 —2.2 Paper Cover Inside● Paper cutterUsed to cut paper at the time of paper setting or at the end of printing.● Print (thermal) headPrints chara
— 15 —3. PREPARATION3.1 Connecting the AC Adapter and AC Power Cord1. Turn off the printer power.2. Plug in the cable connector of the AC adapter to
WEEE MARK,I\RXZDQWWRGLVSRVHWKLVSURGXFWGRQRWPL[ZLWKJHQHUDOKRXVHKROGZDVWH7KHUHLVDVHSDUDWHFROOHFWLRQV\VWHPVIRUXVHGHOHFWURQLFVSURG
— 16 —PrinterPin Signal2TXD3RXD4RTS6 DSR7SG20 DTRPCSignal PinFG 1TXD 2RXD 3CTS 5DSR 6SG 7DTR 203.2 Connecting Interface CablesTurn off the printer an
— 17 —3.3 Installing the PrinterThe printer can be installed horizontally or on the wall.At the time of shipment, the printer is set for horizontal i
— 18 —InitialSettings1Communication conditionDIP switch setting Internal memory ONsetting methodsetting2 Hand shake XON/XOFF DTR/DSR OFF3 Bit length 7
— 19 —3.5 Adjusting the Paper Near-end Sensor1. Push in the paper near-end sensor unit.2. Move the paper near-end sensor unit to the right and left w
— 20 —4. MAINTENANCE AND TROUBLESHOOTING4.1 Setting/Replacing Paper Rolls1. Pull the cover open button fully toward you.2. Open the paper cover.3. I
— 21 —4.2 Removing Jammed Paper1. Turn the printer power off.2. Open the paper cover.3. Remove the jammed paper including any paper chips remaining.
— 22 —CT-S280 V1.xxxSerial Interface Baud rate : 19200 bps Data bit : 8 bits Parity : None Handshaking : DTR/DSRBuffer Size 4K BytesDip
— 23 —4.6 Error Indication● Paper endPaper empty is detected in two steps: paper near-end and paper end. It causesthe ERROR LED to light. If paper
— 24 —5. OTHER5.1 External Views and Dimensions(Unit: millimeter)106116.560170POWERFEEDERROR
— 25 —5.2 Printing PaperUse the print paper shown in the following table or the paper with equivalentquality.Paper Type Product NameRecommended therm
This printer conforms to the following Standards:The Low Voltage Directive 2006/95/EC, formerly 72/23/EEC,the EMC Directive 2004/108/EC, formerly 89/3
— 26 —5.3 Manual Setting of Memory SwitchMemory switches can be set manually or by a command.For manual setting, refer to the next page.The function
— 27 —Manual Setting of Memory Switch (Memory SW)The memory switch can be selected, changed, or written by the combination ofthree actions: pressing t
— 28 —5. Returning to the memory switch select modeWhen the setting of the desired content is completed, open the paper coverand then close the paper
TE74924-00F1.05E-0904Printed in Japan
IMPORTANT: This equipment generates, uses, and can radiate radio frequency energyand if not installed and used in accordance with the instruction manu
— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. After having readthis manual, keep it in a safe, readily ac
— 2 —SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTLY OBSERVEDBefore using this product for the first time, carefully read these SAFETY PRECAUTIONS.Inc
— 3 —Do not use or store this product in a place where it will be exposed to:● Flames or moist air● Direct sunlight● Hot airflow or radiation from a h
— 4 —Place the printer on a flat, stable surface without vibration.• Otherwise dropping may cause injury.Do not use the printer under the following c
— 5 —PRECAUTIONS IN HANDLING THE PRINTERPlease observe the following precautions for power source and powercord:● Do not plug or unplug the power cord
Comments to this Manuals