Citizen BJ2117-01E Instruction Manual download pdf (Page 7)

9. DIVING MODE

When the watch is immersed in the water, while it is

set in the Time mode and the battery is charged

enough for diving, the water sensor senses the

water and switches the watch to Diving mode to

measure the depth. In the Diving mode, the watch

automatically memorises the maximum depth of the

last dive and the user can recall it after the dive.

* If the function

hand and mode

hand don’t point to

their respectively

specified positions

(mode hand: “DV”

positions, function

hand: “0” position)

when the watch

enters the Diving mode (standby status), adjust the

hand positions referring to “11. MEASURES

AGAINST POSSIBLE PROBLEMS”.

Indication range: 0 to 50 m (0 to 125 ft) deep

(measured every second)

Indication unit: 1 m/5 ft (Decimals of five and above

in the first decimal place are rounded up and anything

under five in the first decimal place is rounded down.

Depth less than 1 m/5 ft is indicated as 0 m/0 ft.)

When the watch reaches the depth of 1 m/5 ft or

more in diving, it starts measuring the depth. In

diving, the indication by the function hand

represents the depth.

• When the depth is less than 1 m/5 ft, the function

hand indicates 0 m/0 ft.

• When the depth exceeds 50 m (125 ft), the function

and stops at the overzone mark (52-seconds posi-

tion) to show that the depth is out of the indication

range. As the diver ascends in the water and the

depth is less than 50 m (125 ft), the watch again

indicates the depth.

(1) Press button

A for 2 seconds after diving or in

the water where it is less than 1 m (5 ft) deep

(depth indication: 0 m/0 ft). The diving mode is

cancelled and the watch returns to the Time

mode.

(2) When the watch is left for 10 minutes after diving

or in the water where it is less than 1 m (5 ft)

deep (depth indication: 0 m/0 ft), the watch

automatically returns to the time mode with

cancellation of diving mode. If the watch is again

immersed in water 1 m (5 ft) or more deep within

10 minutes after the last dive, the new dive is

regarded as a continuation of the last dive and

the watch continues to measure the depth.

>How to recall the memorised maximum depth>

(1) Press button

B in the Time

mode or Diving mode (when

depth indication is 0 m/0 ft).

The function hand indicates the

memorised maximum depth.

(2) To cancel the maximum depth

indication, press button

B again.

* Indication of the memorised

maximum depth continues for 30 seconds and is

automatically cancelled after that.

* The memory of the maximum depth of the last dive

is held until the watch is used in the next dive is

held until the watch is used in the next dive.

* If the maximum depth in diving is less than 1 m (5 ft),

it is not memorised. On the other hand, if the

maximum depth exceeds 50 m (125 ft), it is

memorised as an overzone depth.

* When the watch is used in diving for the first time,

it occasionally shows data stored during inspection

prior to shipment.

10. CHRONOGRAPH MODE

The chronograph function enables this watch to

measure time in units of 1 second for a maximum of

49 minutes 59 seconds. When it has reached 50

minutes, since a time measurement was started, the

chronograph stops measuring time and the hands

move to the reset position.

* If the watch is left in reset status in the chronograph

mode for 3 minutes, it automatically switches to

the Time mode.

(1) In the Time mode, press and hold button

Afor

2 seconds or more to switch the watch to

Chronograph mode. As a result, both the

function hand and mode hand quickly go to their

respective “0” positions and then stop.

(2) Each time button

B is pressed, both the hands

start and stop alternately.

(3) If button

A is pressed while both the hands are

stopped, the chronograph is switched to the

reset status.



A: Press the button



B: Press the button



* Wet detection error indication

If the diving standby mode (water sensor in

action) continues for 1 hour or more, the function

hand points at the overzone mark.

If the watch remains in this status for a long time,

refer to “11. MEASURES AGAINST POSSIBLE

PROBLEMS.”

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Citizen BJ2117-01E Instruction Manual Page 7

Comments to this Manuals

Related products and manuals for Watches Citizen BJ2117-01E