Citizen BJ2117-01E Instruction Manual download pdf (Page 8)

12. SETTING FUNCTION HAND AT “0” POSITION

(1) Set the watch to the

Time mode or

Chronograph mode.

(2) Press buttonAor Bto

set the function hand to

the “0” position.

(3) Press the crown into the

normal position and turn

it until it is tightly

screwed against the

case.

* The aforementioned procedure is effectual only

when the hand is located within 15 graduations

before/after the “0” point. When the hand is

located outside the adjustable range, correct the

“0” position of the hand referring to “13. ALL

RESET/ ADJUSTING HAND POSITION”.

* If the watch has been left without any operation

for 3 minutes or longer as the crown is pulled to

the second click stop position, the function hand

does not move regardless of button operation. If

the watch falls into such condition, press the

crown into the normal position and make a fresh

start to adjust the hand position.

* Before unscrewing and pulling out the crown,

make sure that the crown is not wet.

13. ALL RESET/ADJUSTING HAND POSITION

(1) Unscrew the crown and

pull it out to the second

click stop position.

(2) Press button

AorB

simultaneously. If the

function hand moves

slightly, the watch is

reset in whole

(3) Press button

AorBto

set the function hand

and mode hand to their

respective “0” positions.

Button

A : For adjustment counter clockwise

Button

B: For adjustment clockwise.

* The function hand and the mode hand move

interlocking with each other.

(4) Correct the time indication by turning the crown.

(Refer to “8. ADJUSTING TIME AND DATE

(Time mode)”.)

(5) Press the crown into the normal position and

screw it down tightly against the case. As the

crown is pressed into the normal position, the

watch returns to the Time mode and starts

running.

* After the watch is reset, the function hand

points at “NG” position regardless of remaining

battery power. Approximately 1 hour after

resetting, the function hand will indicate the

charge level. (While the function hand is

indicating “NG”, the watch cannot be switched

to the Diving mode).

(5) * If the ALL RESET/ADJUSTING HAND

POSITION fails in clearing away the trouble,

consult with the store where you purchased the

watch or the nearest Citizen Service Centre

about the trouble.

14. NOTE ON SECONDARY BATTERY

The secondary battery used in this watch is a clean

energy battery that incorporates no toxic

substances such as mercury inside. The secondary

battery has no need of periodical replacement

because it is capable of repeated charging and

discharging.

15. OTHER FUNCTIONS

[Rotating bezel]

The rotating bezel means the rotating ring set on

the rim of the watch case. An elapsed time can be

checked by this rotating bezel.

[How to use the rotating bezel]

On starting a dive, turn the rotating

bezel counterclockwise to set the

triangle mark (∆) to the position

where the minute hand is located.

After that, the minute hand serves

to indicate the elapsed time on the

rotating bezel.

(Example) In the figure on the

right, the minute hand indicates

that 10 minutes has passed since the dive was

started (since the ∆ mark was set at the starting

point).

CAUTION

• The rotating bezel can be turned counterclockwise

only, to avoid malfunction. Be careful not to turn

the rotating bezel clockwise by force, otherwise

the rotating bezel may be damaged.

• When using the rotating bezel, you are advised to

read its indication just as a guideline.

Note that the maximum depth memorised during

the last dive is cleared simultaneously during ALL

RESET.

Automatic time correction function

If it takes 4 minutes or less to adjust the position

of the function hand in the Chronograph mode,

the watch automatically sets the hour, minute and

second hands for the correct time immediately

after the adjustment by the automatic time

correction function. Therefore, if adjustment is

finished within 4 minutes, the watch has no need

of manual time correction. However, if the crown

is turned during adjustment, the watch will not

indicate a correct time. adjustment is not

complete within 4 minutes, you will need to not

only adjust the “0” position of the second indicator

(function hand) in the Chronograph mode but also

to set the correct time.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Citizen BJ2117-01E Instruction Manual Page 8

Comments to this Manuals

Related products and manuals for Watches Citizen BJ2117-01E