Citizen iDP-3550 User Manual Page 50
- Page / 174
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
iDP3550/3551 User’s Manual
34
CITIZEN
10.3 Input and Output Signals
10.3.1 Input and Output Signals
(1) RXD
This is a serial received data signal. When a framing error, overrun error, or parity error occurs,
that data is printed as "?".
(2) DTR
When this signal is Ready, write the data or a command. If written at the time of Busy, an overrun
error results, ignoring the previous data. The data can be written in the input buffer even during
printing. Busy is also issued at the time of power -on, test print, on-line, and reset.
(3) TXD
XON (11H) or XOFF (13H) is sent at XON/XOFF control. XON (11H) is sent every 3 seconds in
the Star mode.
When a command is received, that requests the printer state and printer status, 1-byte corresponding
data is output.
(4) DSR
When this signal is a space, the data is sent from the printer side. Note that if this signal is a mark
when a request to send command is executed, the printer will wait until the signal becomes a space.
(5) FAULT
CBM mode
When this signal is Space,a mechanical error has occurred.
Star mode
When this signal is Mark, a mechanical error has occurred.
(6) RESET
A signal to reset the entire printer. (Active Low)
(7) RTS
This signal is turned to Space when the printer is turned on.
- DOT MATRIX PRINTER 1
- Declaration of Conformity 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- Sicherheitshinweis 6
- For Uses in Canada 6
- Pour L’utilisateurs Canadiens 6
- <CAUTIONS> 7
- PRECAUTIONS FOR INSTALLATION 10
- PRECAUTIONS FOR HANDLING 11
- DAILY MAINTENANCE 12
- CONTENTS 13
- 16
- 1. OUTLINE 17
- 2. BASIC SPECIFICATIONS 18
- 2.2 Basic Specifications 19
- 2.3.2 Printing Position 22
- 2.3.3 Cutter Layout 22
- 3.1 iDP3550 23
- 3.2 iDP3551 24
- 4. OPERATION 26
- Setting the initial 30
- General using 30
- CAUTION : • 6.35mm 31
- 4.10 Removing Paper Jam 34
- 4.13 Print Duty 37
- 5. DIP SWITCH SETTING 38
- 5.2 DIP Switches Setting 39
- 6. PRESET JUMPER SETTING 41
- 7. MODE SETTING METHOD 42
- 8.1 Buffer Size 43
- 8.2 Input Buffer Backup 43
- 8.3 Clearing the Input Buffer 43
- 9. PARALLEL INTERFACE 44
- 9.3 Input and Output Signals 45
- 9.3.3 Timing Chart 47
- 9.3.4 Data Receiving Control 47
- 10. SERIAL INTERFACE 48
- 10.3 Input and Output Signals 50
- 10.3.2 Data Configuration 52
- 11. DRAWER KICK-OUT CONNECTOR 55
- 12. WINDER CONNECTOR 56
- 13. MAINTENANCE AND SERVICE 57
- 14. PRINT CONTROL FUNCTIONS 58
- XXXX ALL 59
- FF n (CBM1 Mode) 60
- FF (CBM2 Mode) 60
- SO (CBM1 Mode) 60
- SO (CBM2 Mode) 61
- SI (CBM1 Mode) 61
- SI (CBM2 Mode) 61
- DC1 (CBM1 Mode) 62
- DC1 (CBM2 Mode) 63
- DC2 (CBM1 Mode) 63
- DC2 (CBM2 Mode) 63
- DC3 (CBM1 Mode) 64
- DC3 (CBM2 Mode) 64
- ESC "∗"n1n2 65
- ESC "−"n 65
- ESC "3" 66
- ESC "O" (CBM1 Mode) 67
- (CBM2 Mode) 68
- ESC "f" 1 69
- ESC BEL n1 n2 70
- ESC "P" 0 (iDP3551) 72
- ESC "P" 1 (iDP3551) 72
- 14.2 Star Mode 79
- 14.2.1 Command List 79
- ESC "E" 82
- ESC "F" 82
- ESC "4" 83
- ESC "5" 83
- ESC "z" 85
- ESC "a" n 85
- ESC "C" n 86
- ESC "C" <0> n 86
- ESC "B" [n]k NUL 87
- ESC "N" n 88
- ESC "O" 88
- ESC "l" n 88
- ESC "Q" n 89
- (G raphic Type) 91
- [Function] Text end 101
- [Code] <03>H 101
- *ETX-STX Mode 102
- ESC "t" n 103
- ESC DC3 n 104
- ESC DC2 n1 n2 105
- (Graphic type) 106
- GS ⁄ m (Graphic Type) 107
- 14.3 ESC/POS Mode 108
- 14.3.1 Command List 108
- ESC " " n 110
- ESC "!" n 111
- ESC "%" n 112
- ESC "@" 115
- ESC "D" [n]k NUL 116
- ESC "R" n 117
- ESC "U" n 118
- iDP3550/3551 User’s Manual 119
- ESC "d" n 120
- ESC i (iDP3551 Only) 120
- ESC m (iDP3551 Only) 120
- ESC "p" m n1 n2 121
- ESC "r" n 122
- ESC "u" n 123
- ESC "v" 124
- ESC "{ " n 125
- (Graphic Type) 128
- 15. CHARACTER CODESTABLE 130
- 15.2 CBM (International) 131
- 15.3 Star (Japanese) 132
- 15.4 Star (International) 133
- 15.10 Codepage PC865 (Nordic) 139
- 15.14 Windows Codepage 143
- 128 CITIZEN 144
- (CENTRONICS 145
- Compliant) 145
- (RS-232C Compliant) 145
- Unit: mm 146
- <VORSICHT> 149
- TÄGLICHE WARTUNG 154
- 4. BETRIEB 155
- 4.6 Einlegen des Papiers 158
- Anfangseinstellung 159
- Allgemeine Verwendung 159
- VORSICHT: • 6.35 mm Abstand 160
- 4.9.1 Restpapierrolle 162
- 4.9.2 Endlos-papier 162
- 1 Sek. vergangen 166
- 4.13 Druckvorgang 167
- 5. DIP-SCHALTER-EINSTELLUNG 168
- Bei Auslieferung ab Werk 169
- Automatische Schneideinheit 169
- Werksseitige Einstellung 170
- 2-C Einstellung 171
- iDP3550/3551 User’s Manual 173
- 1.12E-0605 Printed in Japan 174
Related products and manuals for Print & Scan Citizen iDP-3550
Print & Scan Citizen iDP-3540 User Manual
(50 pages)
(50 pages)
Print & Scan Citizen PPU-231 User Manual
(101 pages)
(101 pages)
Print & Scan Citizen 3541 Instruction Manual
(32 pages)
(32 pages)
Print & Scan Citizen S4000L Specifications
(20 pages)
(20 pages)
Print & Scan Citizen CBM-292 User Manual
(105 pages)
(105 pages)
Print & Scan Citizen CD-S500S User Manual
(52 pages)
(52 pages)
Print & Scan Citizen CMP-10BT User Manual
(41 pages)
(41 pages)
Print & Scan Citizen iDP-3535 User Manual
(28 pages)
(28 pages)
Print & Scan Citizen CT-S280 User Manual
(33 pages)
(33 pages)
Print & Scan Citizen CT-S2000L User Manual
(21 pages)
(21 pages)
Print & Scan Citizen CBM-730 User Manual
(31 pages)
(31 pages)
Print & Scan Citizen CLP-7001 User Manual
(76 pages)
(76 pages)
Print & Scan Citizen CT-S280 Specifications
(156 pages)
(156 pages)
Print & Scan Citizen CBM-910 User Manual
(60 pages)
(60 pages)
Print & Scan Citizen iDP-3221 Service Manual
(39 pages)
(39 pages)
Print & Scan Citizen CLP-7002 User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.209 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals