Citizen D700 Instruction Manual Page 10
- Page / 36
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
93
S
S
w
w
i
i
t
t
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
M
M
o
o
d
d
e
e
• The mode changes in the order of standard mode, dive plan mode, scuba log mode, skin
log mode and surface mode each time button (D) is pressed.
• The sub-mode of the standard mode changes in the order of time, travel time, destination
timer, alarm, chronograph, timer and system monitor each time button (A) is pressed in
the standard mode.
• The watch automatically switches to the dive mode (preliminary dive display) when the
water sensor gets wet in any mode (excluding the infrared communication mode and low
power mode).
• The watch switches to the infrared communication mode (initial display) when button (D)
is pressed for at least 2 seconds in any mode (excluding the dive mode and low power
mode).
[Dive Mode
(preliminary dive display)]
* Refer to the section on
" Using the Dive Mode" for
further details.
If the water sensor
gets wet
(A)
(A)
(A)
(A)
(A)
(A)
Button (D) pressed for at
least 2 seconds
[Infrared
Communication Mode
(initial display)]
* Refer to the section on
" Data Communication
Functions" for further details.
Time
Travel time
Destination timer
Alarm
[Standard Mode]
System monitor
Timer
Chronograph
Surface
(only when activated)
Dive Plan
Scuba LogSkin Log
92
About 60% charged to fully charged
Nearly insufficiently charged. Charge
the watch promptly. Since the watch
may become insufficiently charged
during diving, charge the watch
sufficiently before diving.
About 10-20% charged
Insufficiently charged. The watch cannot
be used for diving. Charge the watch
immediately.
* The above illustration provides a
graphic representation of the
amount of residual charge in the
secondary battery and the changes
in the battery charge indicator.
B
B
a
a
t
t
t
t
e
e
r
r
y
y
C
C
h
h
a
a
r
r
g
g
e
e
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
a
a
n
n
d
d
C
C
o
o
n
n
t
t
i
i
n
n
u
u
o
o
u
u
s
s
U
U
s
s
a
a
g
g
e
e
T
T
i
i
m
m
e
e
An approximate indication of the amount of charge remaining in the secondary battery can
be confirmed on the display. The battery charge indicator can be displayed in either the
time mode of the standard mode (location display) or the system monitor mode.
1. How to Read the Battey Charge Indicator
The battery charge indicator changes in the manner shown below according to the amount
of elapsed time the watch has been used.
2. Continuous Usage Time
This watch will continue to run for about 1 month (until the insufficient charge warning
function is activated) once it has been fully charged.
This is roughly based on the conditions of use indicated below.
• Diving (water depth measurement): Twice/week (30 min./dive)
• Alarm: 30 seconds/day
• Chronograph measurement: 1 hour/week
• EL light: 4 seconds/day
*
The continuous usage time of the watch becomes shorter the more often the alarm,
chronograph and other functions are used. In addition, the continuous usage time is further
reduced by infrared communication.
* Since the water sensor is activated when the watch gets wet even when not diving, the
continuous usage time becomes correspondingly shorter.
(
C
)(
B
)
(
D
)(
A
)
(
C
)(
B
)
(
D
)(
A
)
All watch
functions stop.
The "Insufficient Charge Warning Function (BATT
displayed)" is activated at about this time. Charge
the watch immediately. (Refer to the section on
" Warning Functions" for further details.)
Usage
time
Amount of Battery Charge
(A)
(D)
(D)
(D)
(D)
(D)
The watch switches to the "Low
power mode" at about this time.
- Move to this 5
- Watch Display During Charging 6
- 2. Charging the Watch 6
- Fresh Water Diving 7
- Prohibited Use During Diving 7
- 2. Continuous Usage Time 10
- 1. Time Mode 11
- 2. Travel Time Mode 12
- 3. Destination Timer Mode 13
- 4. Alarm Mode 14
- 6. Timer Mode 15
- 5. Chronograph Mode 15
- 7. System Monitor Mode 16
- Flashing 18
- Decompression Diving Warning 19
- Exceed Maximum Depth Warning 19
- Permanent Error Warning 19
- 1. Switching the Display 20
- 3. Dive Alarm 21
- 4. Setting the Dive Alarm 21
- 5. Dive Alarm Monitor 21
- 3. Deleting Log Data 22
- 2. Depth Measurement 23
- 3. Dive Time Measurement 23
- 6. Ending the Dive Mode 24
- 1. Communication Unit 25
- 2. Setting the Time and Date 25
- 2. Infrared Communication 26
- 3. Data Communication with PC 27
- 1. Operating En 28
- 2. Installation 29
- WindowsXP: 30
- Windows2000: 30
- Procedure 32
- NOOKOKOKOK 34
- 0120 78 4807 36
© 2020, manymanuals.com. All rights reserved. | 1.557 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals