Citizen D700 Instruction Manual Page 25
- Page / 36
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D
D
a
a
t
t
a
a
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
i
i
o
o
n
n
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
Data is transferred between watches or between the watch and personal computer using
the data communication functions. There are two ways for transferring data: the first
involves using the communication unit and USB cable provided with the watch, and the
second involves using the infrared communication function.
1. Communication Unit
The communication unit is used when transferring data between the watch and a personal
computer and when charging the watch.
* When transferring data between the watch and a personal computer using the communication unit, the
USB driver software must be installed in the personal computer. (Refer to the section on " Accessory
Software" for information on the procedure for installing the software.)
CAUTION
The communication unit is composed of precision electronic components. Handle with care.
• Store and use the communication unit at a temperature of +10°C to +40°C and humidity
of 20% to 80% (with no condensation of moisture). In addition, avoid storing and using
the communication unit in environments subjected to sudden changes in temperature.
• Avoid storing and using the communication unit in locations subjected to direct sunlight
and high levels of dust. Do not store or use inside an automobile in particular.
• Do not attempt to disassemble or modify the communication unit. This can cause a
malfunction.
• The communication unit does not employ waterproof construction. Do not allow water
to splash on it or allow it to become wet. Make sure the watch is not wet when
attaching to the communication unit.
• Do not use the communication unit in close proximity to a television set or radio. These
can cause problems during data transfer.
• The communication unit is to be used exclusively with CYBER AQUALAND (Movement
No. D700). Do not connect it to the watches of other manufacturers or other models of
Citizen watches.
• Only use the USB cable provided. The use of other cables can result in the occurrence
of electromagnetic interference or other detrimental effects.
• Do not drop the communication unit or subject it to strong impacts. This can cause it to
crack and malfunction.
• Please be aware that the manufacturer is in no way responsible for damages, lost profit
or any other demands from a third party incurred as a result of use of this unit.
• Also be aware that the manufacturer is in no way responsible for damages, lost profit or
any other demands from a third party incurred as a result of repairs or malfunction of
this unit.
Names and Functions of Components
LED (Light Emitting Diode)
This indicates that the communication unit is in the charging state. When the watch is
attached to the communication unit, the LED lights and charging begins. The LED
remains lit during charging and goes out when charging is completed.
USB Cable Connector
This connector is for connecting the communication unit and a personal computer with
the USB cable.
2. Setting the Time and Date
(1) The watch enters the correction state (display is flashing) when
button (C) is pressed for at least 2 seconds during the time
display or date display.
(2) The flashing item changes in the order shown below each time
button (C) is pressed.
(3) Correct the flashing item by pressing button (B).
• Pressing button (B) advances the display by one step at a time. (Pressing button (B)
continuously causes the display to change rapidly.)
• The watch returns to 00 seconds simultaneous to pressing button (B) while
correcting seconds. (The minutes advance by 1 minute if the seconds are between
30 and 59 seconds at that time.)
• When switching the 12H/24H format, the display switches back and forth between
the 12 hour and 24 hour format each time button (B) is pressed.
(4) Pressing button (D) returns the watch to the normal display.
* The time and date of the main location in the time mode of the standard mode can be
displayed and corrected in the low power mode. Changes made to the time and date in the
low power mode are retained even after returning to the time mode of the standard mode.
* The year can be set from 2000 to 2099.
* Dates such as February 30 that do not actually exist are not displayed even during correction.
* Pay attention to AM (A) and PM (P) when using the 12 hour format.
* The day is corrected automatically by correcting the year, month and date.
* The watch automatically returns to the normal display (time display or date display) when none
of the buttons are pressed for about 3 minutes in the correction state (display flashing).
* The watch can be immediately returned to the normal display by pressing button (D) in the
correction state (display flashing).
122 123
Contrast
(CONT)
12H/24H format
switching
Date Month
Seconds Minutes Hours Year
Flashing
(C)
(C) (C) (C)
(C)
(C) (C)
- Move to this 5
- Watch Display During Charging 6
- 2. Charging the Watch 6
- Fresh Water Diving 7
- Prohibited Use During Diving 7
- 2. Continuous Usage Time 10
- 1. Time Mode 11
- 2. Travel Time Mode 12
- 3. Destination Timer Mode 13
- 4. Alarm Mode 14
- 6. Timer Mode 15
- 5. Chronograph Mode 15
- 7. System Monitor Mode 16
- Flashing 18
- Decompression Diving Warning 19
- Exceed Maximum Depth Warning 19
- Permanent Error Warning 19
- 1. Switching the Display 20
- 3. Dive Alarm 21
- 4. Setting the Dive Alarm 21
- 5. Dive Alarm Monitor 21
- 3. Deleting Log Data 22
- 2. Depth Measurement 23
- 3. Dive Time Measurement 23
- 6. Ending the Dive Mode 24
- 1. Communication Unit 25
- 2. Setting the Time and Date 25
- 2. Infrared Communication 26
- 3. Data Communication with PC 27
- 1. Operating En 28
- 2. Installation 29
- WindowsXP: 30
- Windows2000: 30
- Procedure 32
- NOOKOKOKOK 34
- 0120 78 4807 36
© 2020, manymanuals.com. All rights reserved. | 4.929 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals